Matthias Weissers Infopage  Vorträge   Beratung   Kontakt   
eintragen austragen   InterNetWORX
   Seminare   Bücher   Infoletter  
Infopage | Medizin | Energie | Reisen

 Matthias Weisser Logo Matthias Weisser's
alternative Medizin
Hilfe 1 Psyche 2 Statik 3 Ernährung 4 Gifte 5 Zahnherde 6 Störfelder 7 Parasiten
8 heilende Informationen 9 Selbstheilung 10 Diagnostik 11 Zusammenhänge Literatur

Elektromedizin - Pulser Haining
Elektromedizin: welche Geräte gibt es. Welches System kann was?
•  Zapper
•  Zapper diverse: Violet-Ray, EMEM, Beck, F-Scan (englisch)
•  Clark-Zapper, EMEM, Rife-Bare, Beck, Doug, Katze mit Tumor (engl.)
•  Zapper Wade 2127, Rifes Entdeckung BX/Bestätigung Naessens (engl.)
•  Zapper 727 und 2128
•  Zapper III
•  Zapper Wayne, Diagnose
•  Zapper Doug
•  Zapper Weeks-Parker
•  Zapper EMEM2, EMEM3
•  Zapper Veja
•  Zapper Beck Zapper Beck1
•  Zapper CES Beck Brain Tuner
•  Zapper Clark
•  Zapper Emor
•  Pulser Beck
•  Pulser Superthumpy
•  Pulser Haining
•  meine Medizingeräte
Frequenzen finden
•  Frequenzen finden Doug
•  Frequenzen finden Michael Prescott
•  Frequenz-Liste CAFL 2007 englisch
•  Frequenz-Liste AFCAFL 2016 englisch
•  Frequenz-Liste ETDFL 2014 englisch
•  Entgiftungssymptome bei Rife/Bare-Gerät
siehe auch: Elektromedizin

Only one pulser has been made, and that is for use on 240 volts, 50 Hz.

For 110 volts you would probably do better to generate the charging current from a transformer, because if you doubled the number of diodes and capacitors in the ladder network you would also have to double the capacitor value to maintain the same charging time.

The 1M0 resistors are to ensure that the voltage is shared equally between the capacitors and the trigger diodes. The 100pF capacitors may not be necessary, but they help to share the voltage and remove small voltage variations across the trigger devices (surge arrestors).

I soldered some 10 gauge 4 inch long copper wires to each electrode of the surge arrestors to conduct heat away. With a pulse every four seconds the arrestors would otherwise get somewhat hot.

The 1k0 resistors have 850 volts each across them at the instant of firing, so they need to be of 2W or greater power rating. Their purpose is to isolate the charging circuit from the rest so that the transient when the pulse is produced does not damage the charging diodes or capacitors.

Because the coil has 1700 volts across it at firing it might be a good idea to wind it in layers with a layer of insulating tape between each layer of winding. Mechanical movement might otherwise degrade the enamel insulation and lead to short circuits between turns.

2.5 mH produced about 800Hz resonance, 0.5 mH produced about 1500 Hz.

Both coils can throw a 3mm thick, 2 inch diameter aluminum disc 8 feet in the air, and a mild shock can be induced in the hand without contact with the coil.

No guarantees with the circuit, but it worked for me. Take care and remember it can store 1700 volts for a long time if the resistors fail, and the patient could get 1700 volts if a coil lead comes loose...

I don't know if it is powerful enough to have an effect on tumors like the Pappas device and others, but it certainly ought to do much more than Bob Beck's pulser because there is no flash tube to absorb power and the device is resonant at useful Rife frequencies.

If you connect a Rife tube to the coil there is a brilliant flash from the tube, but I don't know whether that would produce any effects on people even though the light must be modulated at twice the resonant frequency.

I wonder what would happen if the coil were to be connected to conducting pads either side of a prominent tumor. Could be very dangerous, but on the other hand the damped wave is only there for a few milliseconds.

Best wishes,

Haining Pulser

© 2000-2017 Weisser